Electronics Assembly Knowledge, Vision & Wisdom
Ask the Experts
Test for Flux Penetration
What is good test for flux penetration through the plated hole barrel?
Ask the Experts

View the Expert comments below.
,{url:'http://www.circuitinsight.com/videos/experts_final.mp4'}], clip:{autoBuffering:true, autoPlay:true, scaling:'scale' } }).ipad();

Arranged via association with Circuitnet..
See the Expert Panel | Submit A Questions | Join the Panel
Ask the Experts Question
Ask the Experts
Test for Flux Penetration
What is good test for flux penetration through the plated hole barrel?
J.V.
Expert's Panel Responses
Flux penetration is important to the flow of solder up into the plated through hole.

The elements which need to be inspected are Flux coverage on the solder source side and flux penetration through the plated through holes.

You can use a glass plate to check for flux coverage on the bottom side of the board. For the plated through hole penetration, use a raw board and apply a thin sheet of absorbent paper on the top side of the board and process it through the fluxer system. You should be looking for flux residues on the absorbent paper sheet. Also look for flux around the pads on the top side of the board.

A specific area to be cautious of is the edges, make sure the flux penetrates the hole near the edges of the board to make sure you get good solder flow in those holes.
image
Leo Lambert
Vice President, Technical Director
EPTAC Corporation
At EPTAC Corporation, Mr. Lambert oversees content of course offerings, IPC Certification programs and provides customers with expert consultation in electronics manufacturing, including RoHS/WEEE and lead free issues. Leo is also the IPC General Chairman for the Assembly/Joining Process Committee.
The tried and true method is to lay a flux sensitive paper over an unpopulated board and pass it over your machine's fluxer. Good penetration will show on the sensitive paper as a discoloration of the paper over (top side) each hole. The sensitive paper may be: pH paper, fax paper, or even a thin brown cardboard stock to see if wetting occurred over the desired holes. The fax and pH papers are nice because they hold the color change while the simple card stock paper will dry fast and thus NOT be a permanent record. The type of paper depends on the flux used and its characteristics: acidity (pH), IPA content, etc.  

There are general tools available for testing flux penetration such as the Fluxometer(r), which uses the method described above, with a "mesh" board to check for uniform flux penetration over the entire fluxed area.
image
Paul Austen
Senior Project Engineer
Electronic Controls Design Inc
Paul been with Electronic Controls Design Inc. (ECD) in Milwaukie, Oregon for over 34 years as a Senior Project Engineer. He has seen and worked with the electronic manufacturing industry from many points of view, including: technician, designer, manufacture, and customer. His focus has been the design and application of thermal process measurement tools used to improve manufacturing processes like: mass reflow and wave soldering, bread baking, paint and powder curing, metal heat treatment and more.
What we used to do was to use a plate with perforations of various sizes arranged in a pattern that repeated on a grid. Over the plate is placed a sheet of paper(1) which is sensitive to the flux and provides a visual indication of contact with the flux. Over that sheet is placed a solid sheet to keep the paper in contact with the perforated plate. The entire "sandwich" is sent through the fluxer, but not the rest of the process. The paper is examined for penetration. The variation in penetration with respect to hole size(2) and in across-conveyor and along-conveyor directions, can be analyzed. Devices similar to the above may be available as a package; we developed and built or own, based on our specific needs.
  1. For alcohol-based fluxes, FAX paper (thermal paper) was used, as the alcohol triggered a blue-black color transition that was clearly visible. This paper is not as common as it used to be, but should still be available. For water-based fluxes, typically a pH-reactive paper is used.
  2. The range of hole sizes used must include holes that are small enough to simulate the behavior of a larger hole with a lead inserted. While the behavior of a smaller, open hole is not identical, it is an acceptable proxy.
image
Fritz Byle
Process Engineer
Astronautics
Fritz's career in electronics manufacturing has included diverse engineering roles including PWB fabrication, thick film print & fire, SMT and wave/selective solder process engineering, and electronics materials development and marketing. Fritz's educational background is in mechanical engineering with an emphasis on materials science. Design of Experiments (DoE) techniques have been an area of independent study. Fritz has published over a dozen papers at various industry conferences.
For selective soldering a simple method is to lay thermal print paper on the top side of the board (without the t/h components in place). Apply the flux as you would normally and look for discoloration of the paper. What you are really after is full barrel wetting and sufficient top side fillets. I suggest using x-ray to see both. Longer but a more positive method is sectioning and microprobe the intermetalic interface. I hope this helps.
image
Alan Cable
President
ACE Production Technologies
Alan Cable, the principle owner of ACE production technologies Inc. has over 40 years experience in the electronics manufacturing arena. Alan's expertise is high production manufacturing automation, equipment design and process engineering. For the past 25 years Alan has focused specifically on soldering issues relating to component solderability, lead tinning and selective soldering, owning several companies with this focus.
You can use a paper on top of the board that is reactive to your specific flux. This is the same method as we (ECD) uses on our Fluxometer product, and paper can be sourced from us directly.
image
Mark Waterman
Engineer / Trainer
Electronic Controls Design, Inc. (ECD)
Mark Waterman is a trainer and field engineer with 17 years experience in service and applications specialties. Intimate knowledge of soldering processes and measurement systems. Six sigma and statistical process control generalist.
Yes there is a simple visual test,  unfortunately the test is only completed on bear PCB boards so it will not produce 100% the side effects of having components in a hole. But the test is useful and helpful to users.

The test uses either thermal fax paper for alcohol based fluxes or pH litmus paper for water based fluxes. The user would then place and secure the test paper down to the topside of a bear assembly and process the vehicle through the fluxer process. The flux atomized spray that penetrated the holes in the PCB would leave a visual imprint on the appropriate test paper that was used. Also there is a test vehicle offered today in the market place by ECD called a Flux-O-Meter. This unit consists of a test vehicle PCB, a pallet with a hold down unit  and the proper tets papers. I hope this information is helpful to you.
John Norton
Eastern Manager
Vitronics Soltec
John Norton started his soldering career in 1983 for Hollis Engineering. He has also worked with Electrovert as a technical training manager and Vitronics Soltec for the last ten years. He has held various technical development and sales positions.
Submit A Comment

Comments are reviewed prior to posting. Please avoid discussion of pricing or recommendations for specific products. You must include your full name to have your comments posted. We will not post your email address.

Your Name


Company


E-mail


Country


Comments


Authentication

Please type the number displayed into the box. If you attempt to submit information and receive an error, you may need to refresh the page and insert the information again.



Related Programs
bullet Hand Soldering Alternative
bullet Test for Flux Penetration
bullet EOS Exposure of Components in the Soldering Process
bullet Selective Soldering Technology Selection
bullet What Causes Solder Fillet Peaks
bullet Exposed Copper Risk
bullet ENIG Solderability Issues
bullet iNEMI Lead-free Wave Soldering Project
bullet Why is Our Selective Soldering Causing Blisters?
bullet Hand Soldering at Low Temperature
More Related Programs
About | Advertising | Contact | Directory | Directory Search | Directory Submit | Privacy | Programs | Program Search | Sponsorship | Subscribe | Terms

Circuit Insight
6 Liberty Square #2040, Boston MA 02109 USA

Jeff Ferry, Publisher | Ken Cavallaro, Editor/Business Manager

Copyright © Circuitnet LLC. All rights reserved.
A Circuitnet Media Publication