Electronics Assembly Knowledge, Vision & Wisdom
Ask the Experts
Humidity Inside Our Screen Printer
Solder paste is drying out after being inside our screen printer for a short time. How can we slow the drying of our solder paste?
Ask the Experts

View the Expert comments below.
,{url:'http://www.circuitinsight.com/videos/experts_final.mp4'}], clip:{autoBuffering:true, autoPlay:true, scaling:'scale' } }).ipad();

Arranged via association with Circuitnet..
See the Expert Panel | Submit A Questions | Join the Panel
Ask the Experts Question
Ask the Experts
Humidity Inside Our Screen Printer

We notice solder paste is drying out after being inside our screen printer for a short time. Humidity inside our screen printer is 35%, while humidity outside our screen printer is 50%.

How can we increase humidity inside our screen printer to help slow the drying of our solder paste?

K. L.
Expert's Panel Responses

Some of the older generation pastes were more susceptible to drying out in low humidity environments and slumping in high humidity environments. This was especially true with water soluble pastes.

Over the last few years we have seen most pastes formulated to withstand lower and higher humidity environments. In the case of water soluble pastes we now have a number of products on the market that are water washable where they have some ingredients that aren't completely water soluble but have surfactants that are able to allow the water to wash away the residue.

This has led to water washable pastes that are less hydroscopic. Also on the No Clean front there has been a change to higher boiling point/low evaporation solvents. This has allowed for pastes to have greater open and abandon times.

Typically these new generation pastes recommend a RH of 25-65% so both your printer and facility would be within specification. My suggestion is to look at the paste rather than increasing the humidity in the printer.

image
Mike Scimeca
President
FCT Assembly
Mike Scimeca created FCT Assembly after the purchase of Fine Line Stencil, Inc., and consists of two major operations: stencil manufacturing and the manufacturing of electronic assembly products such as solder paste, flux and solder bar.

Check with your Solder Paste Printer Manufacturing Company, they may have a fan or A/C unit built into the system to cool the operating mechanics and electronics of the printer.

If this is the case, this might be the cause of your paste drying out. You might need to attach a deflector of shield near the paste bead to protect it from this airflow.

image
Edward Zamborsky
Regional Sales Manager
OK International Inc.
Mr. Zamborsky serves as one of OK's technology advisers to the Product Development group. Ed has authored articles and papers on topics such as; Low Volume SMT Assembly, Solder Fume Extraction, SMT Rework, BGA Rework, Lead Free Hand Soldering, Lead Free Visual Inspection and Lead Free Array Rework.

The solder paste needs to be robust enough to withstand fluctuations in humidity without drying out / slumping.

Increasing humidity inside the printer could cause slump / bridging during reflow.

Typically water-wash pastes are more prone to dryout / slump as they are hygroscopic. No-Clean pastes would be more resistant as they are non-hygroscopic.

image
Karthik Vijay
Technical Manager - Europe
Indium Corp.
Currently with Indium Corporation and responsible for technology programs and technical support for customers in Europe. Over 15 yrs experience in SMT, Power, Thermal & Semiconductor Applications. Masters Degree in Industrial Engg, State University of New York-Binghamton.
Submit A Comment

Comments are reviewed prior to posting. Please avoid discussion of pricing or recommendations for specific products. You must include your full name to have your comments posted. We will not post your email address.

Your Name


Company


E-mail


Country


Comments


Authentication

Please type the number displayed into the box. If you receive an error, you may need to refresh the page and resubmit the information.



Related Programs
bullet Selective Printing for BGA Components
bullet Assembly Options for Handheld Products
bullet Assembling Boards with BGAs on Both Sides
bullet Problems to Look for with Crimp Terminations
bullet How to Clamp Odd Shaped Circuit Boards
bullet Assembly and Reliability Investigation of PoP
bullet Evaluation of Stencil Materials, Suppliers and Coatings
bullet What is Solder Paste Working Life on a Stencil?
bullet How To Calculate Component Standoff Height
bullet Humidity Inside Our Screen Printer
More Related Programs
About | Advertising | Contact | Directory | Directory Search | Directory Submit | Privacy | Programs | Program Search | Sponsorship | Subscribe | Terms

Circuit Insight
6 Liberty Square #2040, Boston MA 02109 USA

Jeff Ferry, Publisher | Ken Cavallaro, Editor/Business Manager

Copyright © Circuitnet LLC. All rights reserved.
A Circuitnet Media Publication