Electronics Assembly Knowledge, Vision & Wisdom
Ask the Experts
How to Clamp Odd Shaped Circuit Boards
If a PCB doesn't have edges to clamp it firmly what solution can you offer to handle boards through an auto routing machine?
Ask the Experts

View the Expert comments below.
,{url:'http://www.circuitinsight.com/videos/experts_final.mp4'}], clip:{autoBuffering:true, autoPlay:true, scaling:'scale' } }).ipad();

Arranged via association with Circuitnet..
See the Expert Panel | Submit A Questions | Join the Panel
Ask the Experts Question
Ask the Experts
How to Clamp Odd Shaped Circuit Boards
If a PCB doesn't have any free edges to hold or clamp the PCB firmly due to components close to the edge, what solution can you offer to handle boards through an auto routing machine?
N. J.
Expert's Panel Responses

Check with the manufacturer of your auto routing machine to see if they offer a tooling plate with tooling pins. These will support and position the board without any edge clamps.

image
Edward Zamborsky
Regional Sales Manager
OK International Inc.
Mr. Zamborsky serves as one of OK's technology advisers to the Product Development group. Ed has authored articles and papers on topics such as; Low Volume SMT Assembly, Solder Fume Extraction, SMT Rework, BGA Rework, Lead Free Hand Soldering, Lead Free Visual Inspection and Lead Free Array Rework.

I would use or buy a vacuum plate, these are available from machine shop supply distributors. They are typically about an inch thick, have a vacuum pump and hose.

Clamp the plate to your router table and lay the PC board on the vacuum plate. The vacuum should easily hold it in place.

Hope that solves your problem.

Now I am curious how you plan to support the board during component assembly and soldering.

image
Ken Bliss
President & CEO - Retired
Bliss Industries, Inc.
Retired - Mr. Bliss has 20+ years experience creating process methods that improve profitability by maximizing hidden unused capacity and throughput. Ken has expertise in all areas of manufacturing specializing in electronics assembly.

"Routing is the most reliable and low-stress option to depaneling assembled PCBs. Odd shaped and small PCBs can be held securely in place until the last cut by means of a custom fixture that is specially designed for the circuit card with pins and side wall mounts.

In addition, the boards are assisted in holding their position with a bottom side vacuum suction that not only secures the board but also keeps dust and debris to a minimum during the depaneling process.

For ease of pick up of multiple assembled circuit boards on one panel after tab cutting, a tray within the fixture can be set to easily lift all boards in one removal step."

image
Michelle Ogihara
Sales and Marketing Manager
Seika Machinery Inc.
Michelle is the Sales and Marketing Manager of Seika Machinery, Inc. She is an active member of the SMTA taking on a past position as Chapter President and currently Secretary, Co-Chairs the MSD Council and serves on several committee positions.

From a stencil viewpoint when the claps are too close to apertures the stencil can not gasket to the board because the clips prevent it.

It is possible to do a relief etch on the bottom side of the stencil in the area of the clips to allow good gasketing. This is a common practice and is effective.

image
Bill Coleman
Vice President Technology
Photo Stencil
For over 18 years, Dr. Coleman has been the vice president of technology for Photo Stencil, working closely with customers to understand their printing requirements. His efforts have resulted in several new stencil products.
There are solutions out there. Fixturing can be created for almost anything - I suggest you to get in touch with a fixture/pallet manufacturer. You will be amazed by the solutions diversity that they can offer. For more questions and/or complete root cause analysis and solutions please contact me. See below.
image
Georgian Simion
Engineering and Operations Management
Independent Consultant
Georgian Simion is an independent consultant with 20+ years in electronics manufacturing engineering and operations.
Contact me at georgiansimion@yahoo.com.
Reader Comment

Laser populated board routing is up and coming due to the eased of fixturing, plus other benefits. No lateral force on the pcb and vision alignment allows the use of a vacuum chuck tooling. Component placement near the edges is less of an issue as no tool clearance or pressure-foot to vacuum debris is needed. Laser beam diameters vary by laser source but can be in the range of 0.001" to 0.008". No dust and no static discharge.

Jon Krum, RITE USA
Submit A Comment

Comments are reviewed prior to posting. Please avoid discussion of pricing or recommendations for specific products. You must include your full name to have your comments posted. We will not post your email address.

Your Name


Company


E-mail


Country


Comments


Authentication

Please type the number displayed into the box. If you receive an error, you may need to refresh the page and resubmit the information.



Related Programs
bullet Revolutionary Printing Solution for SMT Assembly
bullet Low Surface Energy Coatings Rewrite Area Ratio Rules
bullet Past, Present, Future of Solderless Assembly
bullet Stencil Printing of Small Apertures
bullet Jetting Strategies for mBGAs
bullet Pick and Place Placement Rate
bullet Stencil Considerations - Miniature Components
bullet Selective Printing for BGA Components
bullet Assembly Options for Handheld Products
bullet Assembling Boards with BGAs on Both Sides
More Related Programs
About | Advertising | Contact | Directory | Directory Search | Directory Submit | Privacy | Programs | Program Search | Sponsorship | Subscribe | Terms

Circuit Insight
6 Liberty Square #2040, Boston MA 02109 USA

Jeff Ferry, Publisher | Ken Cavallaro, Editor/Business Manager

Copyright © Circuitnet LLC. All rights reserved.
A Circuitnet Media Publication